Stove & range repair · Saanich, BC

Stove Repair Saanich

Dead burners, clicking igniters, weak flames or controls that won't respond.

We handle stove and range repair in homes across Saanich, on electric coil, glass-top, induction and gas cooktops. Whether a burner won't heat, an element is stuck on high, the igniter won't stop clicking or the glass top has cracked, a technician comes to your kitchen, finds the fault and works on it there.

01A burner or element won't heat

One zone stays cold while the others work fine. On coil stoves it's often the element or the socket it plugs into; on glass tops, the element under the glass or its switch.

  • Often
  • Coil element
  • Burner receptacle
  • Radiant element
  • Infinite switch
02The igniter keeps clicking

Clicking that won't stop, even with the knob off, usually comes after a spill or cleaning. If it keeps going once everything is dry, a switch or the spark module is at fault.

  • Often
  • Moisture
  • Igniter switch
  • Spark module
03A gas burner won't light, or the flame is weak

A small, yellow or uneven flame usually means the burner isn't getting a clean mix of gas and air. No flame at all points to the igniter or the burner itself.

  • Often
  • Clogged burner ports
  • Misaligned burner cap
  • Igniter
  • Gas valve
04An element is stuck on high

If a burner glows red no matter where the knob is set, the part that regulates its power has failed. Turn it off at the breaker if it won't shut off.

  • Often
  • Infinite switch
  • Relay on control board
05The glass cooktop is cracked or chipped

Even a small crack can spread with heat and let spills reach the wiring below. Stop using the cooktop until the glass has been replaced.

  • Often
  • Glass top replacement
  • Damaged element below
06Knobs or touch controls don't respond

Loose knobs, dead touch panels or a display that flashes a code often come down to the controls themselves. Check the control lock isn't on first.

  • Often
  • Control knob or switch
  • Touch panel
  • Control board
07Induction zone won't detect the pan

If a zone flashes or shuts off with a pan that has worked before, the detection circuit or the cooling fan may be the cause.

  • Often
  • Induction board
  • Pan sensor
  • Cooling fan

Symptoms

What is your stove doing?

The cooktop and range problems we see most in Saanich kitchens, with the parts that usually cause them. The technician confirms the actual fault on site before any repair.

Smell gas? Don't touch any switches. Leave the house and call your gas utility or 911 from outside.

Stove and range brands we repair

Don't see yours? (250) 999-3866

01Samsung
02LG
03Whirlpool
04GE
05Frigidaire
06KitchenAid
07Maytag
08Bosch
09Electrolux
10Kenmore
11Miele
12Amana

Before you call, four quick checks

Only with the cooktop off and cool.

  1. 1

    Breaker

    Electric ranges run on a double breaker. A half-tripped one can leave some burners working and others dead.

  2. 2

    Burner seating

    Coil elements should push fully into their socket, and gas burner caps should sit flat and centred.

  3. 3

    Clean and dry

    Spills around a gas burner cause clicking and weak flames. Wipe it, let it dry fully, then try again.

  4. 4

    Cookware and lock

    Induction needs magnetic pans. Also check the control lock isn't switched on.

Still not heating, or something doesn't look right? Book a stove repair and we'll take a look.

Book a repair

Book your stove repair in Saanich

Send your details and we'll call back to go over the stove or range and set up a visit. Or call (250) 999-3866.

Service requestStove · Saanich, BC